Discharge Rate Research Articles

Waste heat recovery of blast furnace slag in moving bed: Influencing of structural parameters and operating parameters

Physical recovery of waste heat from blast furnace slag (BFS) by a moving bed is a promising solution. The heat recovery of BFS is mainly achieved through gas–solid heat exchange with cold air and solid–solid heat exchange with water in a moving bed. In this study, the heat transfer process of BFS particles with a particle size ranging from 0.5 mm to 3.0 mm in a rectangular, trapezoidal variable cross-section moving bed was analyzed numerically. The influence of structural parameters and operating parameters of variable cross-section moving beds on heat recovery of BFS was studied. The research found when the inclination angle of the moving bed was 50°, the cooling airspeed was 0.3 m·s−1, and the discharge rate was 0.9 g·s−1, it can not only satisfy the cooling of particles below 400 K, but also ensure that the cooling efficiency of the particles in the bed was higher than 92 %. In this working condition, the improvement of cooling effect and the suppression of reheating could be realized at the same time. Meanwhile, the impact caused by excessive airspeed was weakened, and so was wall wear and dust removal device complexity. The study also found that laying a water-cooled wall can reduce the area of the dead zone of heat exchange and the particle temperature in the dead zone and ensure that the discharge temperature was lower than 380 K.

What is happening with frequency and occurrence of the maximum river discharges in Bosnia and Herzegovina?

In this study, we explored the frequency and occurrence rate of maximum river discharges in the Una and Sana rivers, to understand hydrological variations amidst climate change. We categorized maximum discharges into severe (Una River M1 > 98.2 m3/s; Sana River M1 > 118.2 m3/s) and extreme (Una River, M2, > 123.4 m3/s; Sana River M2 > 246.4 m3/s) events, and identified trends in these events, crucial for assessing environmental impacts. Our findings reveal a nuanced pattern: both rivers experience an increase in severe events from 58 to 55 and 56 to 54 days return period respectively, indicating complex hydrological dynamics. The trends underscore the significant shifts in annual event occurrences, the evolving nature of river systems and underscore the necessity for adaptive management strategies.

Retrospective evaluation of the prevalence and risk factors associated with red blood cell transfusions in cats with urethral obstruction (2009-2019): 575 cases.

To evaluate the prevalence of red blood cell (RBC) transfusions and factors associated with the need for transfusion in cases of feline urethral obstruction (FUO). Secondarily, to compare survival to discharge in cats receiving an RBC transfusion versus those that did not. Retrospective, multi-institutional study from 2009 to 2019. Four university teaching hospitals. Six hundred twenty-two total occurrences of FUO in 575 cats. None. Medical records were retrospectively reviewed for pertinent information. The overall prevalence of severe anemia (PCV<0.20L/L [<20%]) at presentation was 1.0% (6/622). The prevalence of RBC transfusions during hospitalization was 2.1% (13/622). Cats that received an RBC transfusion weighed significantly less than those that did not (4.9 vs 5.8kg; P=0.034) and had a lower PCV at presentation (0.30L/L [30%] vs 0.41L/L [41%]; P<0.001). Hospitalization time (240 vs 72h) and indwelling urinary catheter time (168 vs 48h) were significantly longer in cats receiving a transfusion compared with those that did not (P<0.001). Creatinine concentrations were not significantly associated with transfusion administration, while BUN was higher in cats receiving a transfusion (15.35mmol/L [43mg/dL] vs. 11.78mmol/L [33mg/dL]; P=0.043). Transfusion rates were significantly higher in cats undergoing perineal urethrostomy (5.5%) compared with those that did not undergo surgery (0.97%; P<0.001). The overall survival to discharge rate was 96%. Cats not receiving an RBC transfusion were significantly more likely to survive to discharge than those that did (odds ratio: 14.7, 95% confidence interval: 1.8-37; P<0.001). FUO is rarely associated with severe anemia and the need for RBC transfusions. In this study, cats receiving an RBC transfusion were less likely to survive to discharge; therefore, requiring a blood transfusion may be associated with a worse prognosis. In addition, the need for surgical intervention was associated with a higher prevalence of RBC transfusions.

Definitions and adverse outcomes of sarcopenia in older patients in orthopedic and trauma care: A scoping review on current evidence.

Sarcopenia, defined as the loss of muscle mass and strength, can hinder postoperative recovery and raise mortality rates. However, the current evidence on the harmful effects of sarcopenia in older patients in orthopedic and trauma care is unclear. This scoping review investigates different definitions that were used for the diagnosis of sarcopenia in older patients in orthopedic and trauma care and what adverse consequences have been examined. We performed a comprehensive literature search in PubMed and Embase, following the PRISMA guidelines. We included original studies that examined clinical outcomes (such as length of hospital stay, rate of non-home discharge, rate of subsequent falls, rate of refractures, mortality, and functional outcome/quality of life) in older patients in orthopedic and trauma care (aged 65 years and above) with diagnosed sarcopenia (S) compared to a group without sarcopenia (NS). Our search identified 2,748 publications. Out of these, 23 articles met the inclusion criteria. Most publications were from Asia (n = 13). A total of 6174 patients were examined, with a prevalence of sarcopenia in 14-92%. 11 articles focused on patients with hip joint pathologies. Most studies diagnosed sarcopenia according to the Asian Working Group on Sarcopenia (AWGSOP1 or AWGSOP2) definitions (n = 10). Length of hospital stay was investigated in 13 studies. Seven studies assessed rates of non-home discharge rates. Subsequent falls were not investigated in any of the studies. 1 study reported the overall refracture rate (S: 10.4%; NS: 5.8%). Mortality was assessed in 11 studies (S: 1-60.5%; NS: 0-39.5%). The functional outcome/quality of life was investigated by 17 studies (Barthel Index decline S: -4.5 to -15.3 points; NS: -11.7 to -54.7 points). Sarcopenia has been increasingly studied in older patients in orthopedic and trauma care but there is a lack of consistent definition criteria. This scoping review suggests that sarcopenia may be associated with prolonged length of stay, higher rates of non-home discharge, and increased mortality among older patients in orthopedic and trauma care. However, prospective studies are necessary to establish the relationship between sarcopenia and refractures, falls, and functional outcome/quality of life among older patients in orthopedic and trauma care.

Investigating the Effect of the Separation of Scales in Reduced Order Battery Modelling: Implications on the Validity of the Newman Model

Abstract Modelling lithium-ion battery behaviour is essential for performance prediction and design improvement. However, this task is challenging due to processes spanning many length scales, leading to computationally expensive models. Reduced order models have been developed to address this, assuming a "separation of scales" between micro- and macroscales. This study compares two approaches: direct microstructure-resolved 3D domain electrochemical modelling and a simplified 1D homogenized model, similar to the Doyle-Fuller-Newman model. &amp;#xD;&amp;#xD;The research investigates the validity of the scale separation assumption in continuum electrode-level models by varying scale separation factors, boundary conditions, and geometries. The findings reveal that in 3D models, more tortuous, less porous microstructures deviate more from 1D predictions, especially under higher discharge rates. However, under realistic conditions, with an electrode featuring eight particles across its thickness and typical transport properties, the 3D model predicts only a slight (2%) increase in current compared to the 1D model at a high rate of 7C (approximately 350 A/m²).&amp;#xD;&amp;#xD;These results suggest that the separation of scales assumption in the DFN model is generally suitable for a wide range of operating conditions. However, 1D models may overlook local variations in electrolyte concentration and potential, crucial for understanding degradation mechanisms.&amp;#xD;

The construction of an asymmetric hybrid supercapacitor with 2D materials MXene and perovskite

The construction of an asymmetric hybrid supercapacitor with 2D materials MXene and perovskite

High Energy Storage Performance in BiFeO3-Based Lead-Free High-Entropy Ferroelectrics.

Dielectric capacitors are widely used in advanced electrical and electronic systems due to the rapid charge/discharge rates and high power density. High comprehensive energy storage properties are the ultimate ambition in the field of application achievements. Here, the high-entropy strategy is proposed to design and fabricate single-phase homogeneous (Bi0.5Ba0.1Sr0.1Ca0.2Na0.1)(Fe0.5Ti0.3Zr0.1Nb0.1)O3 ceramic, the hierarchical heterostructure including rhombohedral-tetragonal multiphase nanoclusters and locally disordered oxygen octahedral tilt can lead to the increased dielectric relaxation, diffused phase transition, diverse local polarization configurations, grain refinement, ultrasmall polar nanoregions, large random field, delayed polarization saturation and improved breakdown field. Accordingly, a giant Wrec ≈13.3 J cm-3 and a high η ≈78% at 66.4kV mm-1 can be simultaneously achieved in the lead-free high-entropy BiFeO3-based ceramic, showing an obvious advantage in overall energy-storage properties over BiFeO3-based lead-free ceramics. Moreover, an ultrafast discharge rate (t0.9 = 18ns) can be achieved at room temperature, concomitant with favorable temperature stability in the range of 20-160 °C, due to the enhanced diffuse phase transition and fast polarization response. This work provides a feasible pathway to design and generate dielectric materials exhibiting high comprehensive energy-storage performance.

Direct reconstruction of the temperature field of lithium-ion battery based on mapping characteristics

Lithium-ion (Li-ion) batteries are susceptible to the working temperature so that the monitoring is essential to the battery internal temperature. The electrochemical-thermal coupling model completely reflects the battery internal behavior. However, the high complexity and multi-field coupling make it difficult to be applied to reconstruct the battery temperature field based on state observer. Based on mapping characteristics, this work proposes a temperature field direct reconstruction scheme. And the electrochemical-thermal coupling model plays a large role in this scheme. Mapping characteristic vectors of the transient temperature field are obtained from the step response model of the Li-ion battery temperature field to charge and discharge current. Furthermore, the quantitative connection of the mapping characteristic vectors between the surface points of and the internal nodes of the battery is characterized by a relevance degree matrix. And a direct reconstruction model of the internal transient temperature field is established. The internal temperature field is reconstructed directly online and in real time via exploiting the temperature measurements on battery surface. In numerical experiments, the three-dimensional temperature field of the Li-ion battery charge and discharge processes is reconstructed. The effects of charge and discharge rates, model mismatch, and measurement errors on the reconstruction results are investigated. During the charge and discharge processes, the maximum values of the transient average error of the reconstructed temperature field are about 0.4 K and 0.3 K, respectively. And the transient average error is generally below 0.8 K when the standard deviation of measurement errors is 0.5 K.

Does Single Dose Epinephrine Improve Outcomes for Patients with Out-of-Hospital Cardiac Arrest and Bystander CPR or a Shockable Rhythm?

ABSTRACT Background: A single dose epinephrine protocol (SDEP) for out-of-hospital cardiac arrest (OHCA) achieves similar survival to hospital discharge (SHD) rates as a multidose epinephrine protocol (MDEP). However, it is unknown if a SDEP improves SHD rates among patients with a shockable rhythm or those receiving bystander cardiopulmonary resuscitation (CPR). Methods: This pre-post study, spanning 11/01/2016-10/29/2019 at 5 North Carolina EMS systems, compared pre-implementation MDEP and post-implementation SDEP in patients ≥18 years old with non-traumatic OHCA. Data on initial rhythm type, performance of bystander CPR, and the primary outcome of SHD were sourced from the Cardiac Arrest Registry to Enhance Survival. We compared SDEP vs MDEP performance in each rhythm (shockable and non-shockable) and CPR (bystander CPR or no bystander CPR) subgroup using Generalized Estimating Equations to account for clustering among EMS systems and to adjust for age, sex, race, witnessed arrest, arrest location, AED availability, EMS response interval, and presence of a shockable rhythm or receiving bystander CPR. The interaction of SDEP implementation with rhythm type and bystander CPR was evaluated. Results: Of 1690 patients accrued (899 MDEP, 791 SDEP), 19.2% (324/1690) had shockable rhythms and 38.9% (658/1690) received bystander CPR. After adjusting for confounders, SHD was increased after SDEP implementation among patients with bystander CPR (aOR 1.61, 95%CI 1.03-2.53). However, SHD was similar in the SDEP cohort vs MDEP cohort among patients without bystander CPR (aOR 0.81, 95%CI 0.60-1.09), with a shockable rhythm (aOR 0.96, 95%CI 0.48-1.91), and with a non-shockable rhythm (aOR 1.26, 95%CI 0.89-1.77). In the adjusted model, the interaction between SDEP implementation and bystander CPR was significant for SHD (p = 0.002). Conclusion: Adjusting for confounders, the SDEP increased SHD in patients who received bystander CPR and there was a significant interaction between SDEP and bystander CPR. Single dose epinephrine protocol and MDEP had similar SHD rates regardless of rhythm type.

Development of a feasible and scalable manufacturing method for PTFE-based solvent-free lithium-ion battery electrodes

Conventional wet-electrode manufacturing encounters challenges in producing thicker electrodes due to issues related to solvent evaporation. This study introduces a novel method for fabricating solvent-free dry electrodes using polytetrafluoroethylene (PTFE) as a binder, representing a significant advancement in electrode manufacturing processes. By eliminating the use of solvents, this method not only addresses these challenges but also offers a scalable and practical solution for mass production. The process is meticulously structured into sequential unit operations, each specifically tailored for a distinct function, utilizing the distinctive fibrillation properties of PTFE. Intermediate product specifications for each phase are clearly defined, accompanied by a comprehensive analysis of both physical and electrochemical performances. This analysis highlights the influence of varying PTFE contents and properties on the microstructure of the dry electrode. Notably, the study achieves a significant breakthrough with an electrode formulation of NCM811/PTFE/carbon black (CB)/carbon nanotube (CNT) = 96/2.0/1.8/0.2, which demonstrates exceptional discharge rate capability of 80 % at a 0.5 C-rate (5 mA/cm2) under the demanding parameters of 10 mAh/cm2 and 3.8 g/cc. This approach not only enhances the microstructural properties of dry electrodes but also paves the way for environmentally friendly and efficient electrode manufacturing for future energy storage applications.

Improving Patient Outcomes Using Measures to Increase Discharge Rates to Home

Improving Patient Outcomes Using Measures to Increase Discharge Rates to Home

Improving thermal conductivity of styrene ethylene butylene styrene/paraffin/boron nitride phase change composite via the sacrificial template method for battery thermal management

To address the bottleneck of easy leakage and low thermal conductivity of phase change materials (PCMs) for battery thermal management. Phase change composite (PCCs) with paraffin (PA) as the PCM, styrene ethylene butylene styrene (SEBS) as the supporting skeleton, and boron nitride (BN) as the thermally conductive filler were fabricated by the sacrificial template method. Compared with the composite prepared by melt-blending method, the thermal conductivity of PCC was improved by 27.6 % and the leakage rate was reduced by 82.4 % because the BN was rubbed with Na2SO4 under the shear provided by internal mixer. As a result, the maximum temperature and maximum temperature difference of the battery pack with PCC cooling were 35.8 % and 62.5 % lower than those without PCC cooling at 2C discharge rate. In total, this work offers a strategy for improving the thermal conductivity and the leakage-proof ability of PCCs as well as for large-scale fabrication.

Thermal Optimization Strategies for Li-Ion Batteries: Predictive Temperature Algorithm

Abstract Performance, safety, and longevity of batteries are all strongly impacted by thermal management, which is an essential component of battery design and operation. This work examines how accurate temperature control can result in significant improvements in performance and reliability with a focus on battery thermal heating. Predicting the temperature achieved by the battery during operation not only avoids conditions that lead to thermal runaway, but also guarantees that the battery is used optimally within an optimal temperature range. Within the optimal temperature range several advantages are observed. First, battery efficiency improves significantly as electrochemical processes occur more efficiently. Furthermore, by lowering the possibility of short circuits and improving overall battery safety, thermal stability aids in the prevention of undesirable phenomena like dendrite growth. By lessening the deterioration brought on by thermal degradation processes, thermal optimization also affects battery longevity. Based on experimental tests, a Finite Element Model (FEM) is developed. A model for thermal runaway propagation is established by combining thermal runaway and conduction models with an Arrhenius law-based combustion model. The study employed a cylindrical Li-Ion cell to conduct tests, taking into account three parameters: discharge rate (CRate), ambient temperature (Tamb), and initial battery temperature (T0). An algorithm based on the three variables was developed using the simulation results. The algorithm enables the accurate prediction of rising battery temperature during use, facilitating the setting of an optimal maximum discharge rate considering initial and ambient temperatures, thereby ensuring optimal performance within the desired temperature range.

Sodium oligomannate activates the enteroendocrine-vagal afferent pathways in APP/PS1 mice.

Enteroendocrine cells (EECs) and vagal afferent neurons constitute functional sensory units of the gut, which have been implicated in bottom-up modulation of brain functions. Sodium oligomannate (GV-971) has been shown to improve cognitive functions in murine models of Alzheimer's disease (AD) and recently approved for the treatment of AD patients in China. In this study, we explored whether activation of the EECs-vagal afferent pathways was involved in the therapeutic effects of GV-971. We found that an enteroendocrine cell line RIN-14B displayed spontaneous calcium oscillations due to TRPA1-mediated calcium entry; perfusion of GV-971 (50, 100 mg/L) concentration-dependently enhanced the calcium oscillations in EECs. In ex vivo murine jejunum preparation, intraluminal infusion of GV-971 (500 mg/L) significantly increased the spontaneous and distension-induced discharge rate of the vagal afferent nerves. In wild-type mice, administration of GV-971 (100 mg· kg-1 ·d-1, i.g. for 7 days) significantly elevated serum serotonin and CCK levels and increased jejunal afferent nerve activity. In 7-month-old APP/PS1 mice, administration of GV-971 for 12 weeks significantly increased jejunal afferent nerve activity and improved the cognitive deficits in behavioral tests. Sweet taste receptor inhibitor Lactisole (0.5 mM) and the TRPA1 channel blocker HC-030031 (10 µM) negated the effects of GV-971 on calcium oscillations in RIN-14B cells as well as on jejunal afferent nerve activity. In APP/PS1 mice, co-administration of Lactisole (30 mg ·kg-1 ·d-1, i.g. for 12 weeks) attenuated the effects of GV-971 on serum serotonin and CCK levels, vagal afferent firing, and cognitive behaviors. We conclude that GV-971 activates sweet taste receptors and TRPA1, either directly or indirectly, to enhance calcium entry in enteroendocrine cells, resulting in increased CCK and 5-HT release and consequent increase of vagal afferent activity. GV-971 might activate the EECs-vagal afferent pathways to modulate cognitive functions.

State of Health Estimation for Lithium-Ion Battery Based on Sample Transfer Learning under Current Pulse Test

Considering the diversity of battery data under dynamic test conditions, the stability of battery working data is affected due to the diversity of charge and discharge rates, variability of operating temperature, and randomness of the current state of charge, and the data types are multi-sourced, which increases the difficulty of estimating battery SOH based on data-driven methods. In this paper, a lithium-ion battery state of health estimation method with sample transfer learning under dynamic test conditions is proposed. Through the Tradaboost.R2 method, the weight of the source domain sample data is adjusted to complete the update of the sample data distribution. At the same time, considering the division methods of the six auxiliary and the source domain data set, aging features from different state of charge ranges are selected. It is verified that while the aging feature dimension and the demand for target domain label data are reduced, the estimation accuracy of the lithium-ion battery state of health is not affected by the initial value of the state of charge. By considering the mean absolute error, mean square error and root mean square error, the estimated error results do not exceed 1.2% on the experiment battery data, which highlights the advantages of the proposed methods.

Full robotic versus open ALPPS: a bi-institutional comparison of perioperative outcomes.

In primarily unresectable liver tumors, ALPPS (Associating Liver Partition and Portal Vein Ligation for Staged hepatectomy) may offer curative two-stage hepatectomy trough a fast and extensive hypertrophy. However, concerns have been raised about the invasiveness of the procedure. Full robotic ALPPS has the potential to reduce the postoperative morbidity trough a less invasive access. The aim of this study was to compare the perioperative outcomes of open and full robotic ALPPS. The bicentric study included open ALPPS cases from the University Hospital Zurich, Switzerland and robotic ALPPS cases from the University of Modena and Reggio Emilia, Italy from 01/2015 to 07/2022. Main outcomes were intraoperative parameters and overall complications. Open and full robotic ALPPS were performed in 36 and 7 cases. Robotic ALPPS was associated with less blood loss after both stages (418 ± 237ml vs. 319 ± 197ml; P = 0.04 and 631 ± 354ml vs. 258 ± 53ml; P = 0.01) as well as a higher rate of interstage discharge (86% vs. 37%; P = 0.02). OT was longer with robotic ALPPS after both stages (371 ± 70min vs. 449 ± 81min; P = 0.01 and 282 ± 87min vs. 373 ± 90min; P = 0.02). After ALPPS stage 2, there was no difference for overall complications (86% vs. 86%; P = 1.00) and major complications (43% vs. 39%; P = 0.86). The total length of hospital stay was similar (23 ± 17days vs. 26 ± 13; P = 0.56). Robotic ALPPS was safely implemented and showed potential for improved perioperative outcomes compared to open ALPPS in an experienced robotic center. The robotic approach might bring the perioperative risk profile of ALPPS closer to interventional techniques of portal vein embolization/liver venous deprivation.

Supraspinal, spinal, and motor unit adjustments to fatiguing isometric contractions of the knee extensors at low and high submaximal intensities in males.

Contraction intensity is a key factor determining the development of muscle fatigue and it has been shown to induce distinct changes along the motor pathway. The role of cortical and spinal inputs that regulate motor unit (MU) behaviour during fatiguing contractions is poorly understood. We studied the cortical, spinal, and neuromuscular response to sustained fatiguing isometric tasks performed at 20 and 70% of the maximum isometric voluntary contraction (MVC), together with MUs behaviour of knee extensors in healthy active males. Neuromuscular function was assessed before and after performing both tasks. Cortical and spinal responses during exercise were measured via stimulation of the motor cortex and spinal cord. High density electromyography was used to record individual MUs from the vastus lateralis (VL). Exercise at 70% MVC induced greater decline in MVC (p = 0.023), and potentiated twitch force compared to 20%MVC (p < .001), with no difference in voluntary activation (p = 0.514). Throughout exercise, corticospinal responses were greater during the 20%MVC task (p < 0.001), and spinal responses increased over time in both tasks (p ≤ 0.042). MU discharge rate increased similarly following both tasks (p ≤ 0.043) while recruitment and de-recruitment thresholds were unaffected (p ≥ 0.295). These results suggest that increased excitability of cortical and spinal inputs might be responsible for the increase in MU discharge rate. The increase in evoked responses together with the higher MUs discharge rate might be required to compensate for peripheral adjustments to sustain fatiguing contractions at different intensities.

A Multinational, Multicentre Study Mapping Models Of Kidney Supportive Care Practice

IntroductionKidney supportive care (KSC) integrates kidney and palliative care to improve quality of life for people with chronic kidney disease. Despite increasing interest and global advocacy to integrate KSC into kidney care, evidence to guide optimal care delivery is limited. MethodsThis observational cross-sectional study used an online survey to describe current KSC models in Australia, Aotearoa-New Zealand and the United Kingdom (UK). ResultsBetween April and December 2022, 114 units responded (response rate 67%), with 66% having a dedicated KSC service (UK 74%, Australia 58%, New Zealand 67%). Many different healthcare professionals worked in KSC services with diversity in clinical resources and activities between units and across countries. Overall, funding for KSC services was low, with a median full time equivalent per unit (standardised per 100 people receiving haemodialysis) of 0.51 (interquartile range 0.17-1.05) and 4 units provided a service without allocated funding. The scope of KSC service was wide-ranging and prioritised activities included symptom management, psychological support, complex future treatment planning and discussion, and care coordination. There were no significant differences between countries in terms of location of care provision, frequency of review, referral patterns or discharge rates, but there was variation described within countries. ConclusionModels of KSC vary markedly across kidney units and between countries. Despite this variation there was consistency in terms of clinical priorities which were person-centred and focused on physical and psychosocial wellbeing. Further research is required to evaluate the effectiveness of KSC provision, alongside improved funding methods to ensure sustainable and equitable KSC delivery.

Numerical and experimental analysis of battery thermal management of 21700 Nickel Manganese Cobalt lithium-ion battery

High discharge rates in 21700 NMC Lithium-Ion Batteries (LIBs) leads to elevated temperatures, negatively impacting battery performance and longevity. This study examines the integration of phase change materials to address this issue. Phase change materials absorb heat through sensible and latent heat mechanisms, effectively reducing battery temperature. At discharge rates of 0.5 C, 1 C, and 1.5 C, phase change materials decreased battery temperature by 4.12 %, 7.32 %, and 8.16 %, respectively, ensuring optimal operating conditions. Incorporating phase change materials within battery modules minimizes cell spacing, leading to a smaller battery pack size and reduced costs. This compact design is achieved by exploiting phase change materials ability to store and release large amounts of heat while maintaining a nearly constant temperature. Furthermore, analyzing temperature variations across diverse surfaces within battery modules provides valuable insights for cooling technology development. The integration of Phase Change Materials effectively regulates temperatures, particularly under high discharge rates, offering significant implications for battery performance and longevity. This study highlights the potential of phase change materials in improving LIBs thermal management, which is crucial for electric vehicle applications and other high-power-demand scenarios. By addressing temperature-related challenges, phase change materials integration contribute to the advancement of more efficient, reliable, and safer LIBs.

High thermal conductivity composite phase change material with Zn2+ metal organic gel and expanded graphite for battery thermal management

Phase change materials (PCMs) with promising potential thermal energy is stored and released much thermal energy during phase change process, which has greatly prospect in building energy conservation, waste heat recovery, energy storage, electrical vehicles (EVs) and other fields. Nevertheless, the low thermal conductivity and easy leakage of PCM is still a challenge to restrict its fasting development. Traditional supporting material is hard to reconcile antileakage and thermal conductivity of composite PCM (CPCM). Herein, the polyethylene glycol (PEG) with three-dimensional Zn2+ metal–organic gel (ZnHGL) as high-thermal conductivity support framework, styrene–butadiene–styrene block copolymer (SBS) and expanded graphite (EG) has been designed and prepared PZSE with high thermal conductivity, accompany with double transferring heat and supporting network structure. In contrast with pure PEG, the thermal conductivity of PZSE2 is increased by obvious 8.7 times when Zn2+ metal–organic gel and SBS with the proportion of 1:1, the mass maintenance rate and latent heat storage capacity are increased to 99.5 % and 103.64 J/g, respectively. Further, the thermal imaging camera indicate that PZSE2 exhibit a stable temperature-regulation property, which is benefited to extend the time to adjust the temperature. Additionally, the maximum temperature and temperature differential of the battery module with PZSE2 can be maintained within 60 °C and 6 °C, respectively, even at 1.5C discharge rate after ten cycling process. It indicates that the battery module with PZSE2 has optimum thermal management effect. Therefore, PZSE with metal–organic gel and EG can provide a promising candidate utilization in thermal regulation of EVs and energy storage.